Page 1 of 1

Problems with PVDM2 in a 2800 with E1/T1 Module

Posted: Sat Dec 11, 2010 5:56 pm
by Guest

Hello,I have a 2800 with an E1/T1 Module and PVDM2 Modules and want to dial out over a telnet connection to the modem line.The "show line" command shows only VTY lines and no TTY lines to connect to.The modems are in the pvdm0 Slot of the E1 Card.We have had no such problems doing this with the same E1/T1 Card and NM-xDM( Mica Modems ) in several 3800 Routers.thank you very much for your helpKlaus HebelHere is the configuration:yourname#show inventoryNAME: "2811 chassis", DESCR: "2811 chassis"PID: CISCO2811         , VID: V05 , SN: FCZ1138713MNAME: "High Density Voice2 Network module with on board one port interface ", DESCR: "High Density Voice2 Network module with on board one port interface "PID: NM-HDV2-1T1/E1    , VID: V03 , SN: FOC11402PXVNAME: "PVDMII DSP SIMM with Two DSPs", DESCR: "PVDMII DSP SIMM with Two DSPs"PID: PVDM2-32          , VID: V01 , SN: FOC11416WU0yourname#show runBuilding configuration...Current configuration : 4058 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname yourname!boot-start-markerboot system flash c2800nm-adventerprisek9-mz.124-18.binboot-end-marker!card type e1 1 1logging buffered 51200 warnings!no aaa new-modelno network-clock-participate slot 1!!ip cef!!ip domain name yourdomain.comip auth-proxy max-nodata-conns 3ip admission max-nodata-conns 3!isdn switch-type primary-net5!voice-card 0 no dspfarm!voice-card 1 no dspfarm!!controller E1 1/0 pri-group timeslots 1-31!!interface FastEthernet0/0 description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0/0$ ip address 172.16.1.119 255.255.240.0 duplex auto speed auto!interface FastEthernet0/1 no ip address shutdown duplex auto speed auto!interface Serial1/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice modem no fair-queue no cdp enable!ip forward-protocol nd!!ip http serverip http access-class 23ip http authentication localip http secure-serverip http timeout-policy idle 60 life 86400 requests 10000!access-list 23 permit 10.10.10.0 0.0.0.7!!control-plane!!voice-port 1/0:15!!line con 0 login localline aux 0line vty 0 4 privilege level 15 login local transport input telnet sshline vty 5 15 privilege level 15 login local transport input telnet ssh!scheduler allocate 20000 1000!endyourname#

Re:Problems with PVDM2 in a 2800 with E1/T1 Module

Posted: Sat Dec 11, 2010 7:10 pm
by Guest

Hi, the pvdm2 that you have support only voice calls and do not support modem calls.The modem module in pvdm2 form has part number pvdm2-xdm where x can be 8, 16 or 32.You also need the NM-CE1/T1 module, or the new hwic-1cet1-pri, or the vic2-2bri-nt/te to connect to telco.Hope tis helps, please rate post if it does

Re:Problems with PVDM2 in a 2800 with E1/T1 Module

Posted: Sat Dec 11, 2010 7:13 pm
by Guest

Thank you very much for your quick help!

Re:Problems with PVDM2 in a 2800 with E1/T1 Module

Posted: Sat Dec 11, 2010 8:12 pm
by Guest

You're welcome, thanks for the nice rating and good luck!